ASTRO U 262 User's Guide

User Guide U 262U 262 ASI / IP GatewayUser Guide

5.2 Setting the IP Management interfacesThe „IP Management Settings“ area is used to stipulate the DNS server, to congure up to four SNMP Trap reci

6 Test generatorClicking on the „Test Gen“ submenu takes you to the test generator settings. This internal test generator is able to produce a test

The „Input Mux Settings“ are used to assign an IP TX port to each ASI input of the U 262 Gateway. An ASI stream can also be routed to several IP TX, s

Figure 10: General settings for the reception ports (IP RX Common Settings)If the network infrastructure is of redundant design and if “Data A” and “D

Figure 11: Conguring the transmission port (IP TX1 to IP TX16 Channel Settings)9.3 Destination MACThe “Destination MAC” is obtained automatically f

The first drop-down selection field is used to stipulate the number of columns in the checkingmatrix. There are 1 to 20 columns or the selection “Off”

The “Encapsulation” is selected according to the stipulation of how the input data stream has been encapsulated by the transmission

11 Conguring the output multiplexerClicking on the “Output Mux” submenu takes you to the output multiplexer settingsFigure 14: Example view of the

12 User AdministrationClicking on the „User“ submenu takes you to User administration. When delivered, the U 262 Gateway can be congured us

Figure 16: Analyzing the selected transport streamWait until the „...done!“ message appears. Clicking on the „+“ or „-“ symbols displays or hides the

User Guide U 262Copyright NoticeParts of the software of this product is third-party software, which was developed under several differe

14 LicensingClicking on the „License“ submenu takes you to licensing. The features of the U 262 can be upgraded from the factory-deli

Figure 18: Input mask for the U 262 software update15.2 Update using the example of a TFTP Server for WindowsShould there be no rm (T)FTP server set

The „tftpd32“ program is started directly from the folder with the U 262 update les. In the window that opens, click on the „Settings“ button rst an

16 Log BookClicking on the „System Log“ submenu takes you to the U 262 Gateway‘s log book. This docu-ments all processes which are relevant to operat

17 StatisticsClicking on the „Statistics“ submenu takes you to the statistics relating to the data transfer of the U 262 Gateway. This displays all s

18 Network propertiesThe network properties can be displayed by clicking on the „Network“ submenu. The displayed characteristics are purely informat

19 LogoutClicking on the „Logout“ submenu (only available when you are logged in) allows you to log out from the U 262 Gateway.Figure 25: Logging out

27 User Guide U 26220 Technical DataType U 262 U 262 iOrder number 380 263 380 264Transport stream interfacesDVB ASI 16Connectors BNC jackBitrate [M

ASTRO Strobel Kommunikationssysteme GmbHOlefant 1–3, D-51427 Bergisch Gladbach (Bensberg)Tel.: 0 22 04/405-0, Fax: 0 22 04/405-10eMail: kontakt@astro-

3 User Guide U 262 Inhaltsverzeichnis1 Illustrations ...

1 IllustrationsPower LEDWarning LED Failure LED Display of Management IP addresses BNC ASI input BNC ASI outputs Mains supplyGrounding connectionMAC

52 Introduction2.1 Safety instructionsRemove both mains plugs before opening the device!Exercise caution when servicing the power supply unit. Th

6 User Guide U 262The subscriber network must be and remain grounded as per the regulations in EN 60728 Part 11, even if the device is removed.The equ

3 General introduction3.1 Connecting the U 262 to a PC / LaptopApplying the operating voltage turns on the U 262 automatically. Followin

Figure 2: View of U 262 display and LEDs in the Web browser user interfaceIn the example for gure 2, the device is reporting the error „IP RX4A Data

When the access data have been input correctly, it is possible to continue conguration. For security reasons, the usernames and passwor